st www.vishay.com vishay revision: 03-feb-12 1 document number: 43000 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 supertan ? wet tantalum capacitors with hermetic seal vishay st represents a major breakthrough in wet tantalum capacitor technology. its unique cathode system provides the highest capacitance per unit volume. the design facilitates a doubling of capacitance, lower esr and higher ripple current rating compa red with conventional wet tantalum products. moreover, the st has the capacitance stability of a solid tantalum capacitor and there are no circuit impedance restrictions. the st is housed in an all tantalum, hermetically sealed case and is manufactured to with stand hazardous environments. the st is used widely in the defense and aerospace industries and whenever there is a space problem. performance characteristics operating temperature: - 55 c to + 85 c (to + 125 c with voltage derating) capacitance tolerance: at 120 hz, + 25 c. 20 % standard. 10 % available as special. features ? very high capacitance ? 10 f to 1800 f ?25 v dc to 125 v dc ? very low esr ? high ripple current ? all tantalum case ? hermetically sealed ?low dcl ? axial through-hole terminations: standard tin/lead (sn/pb) 100 % tin (rohs compliant) available ? compliant to rohs directive 2002/95/ec note * pb containing terminations are not rohs compliant, exemptions may apply application notes a. no continuous reverse voltage permissible. b. the peak of the applied ac ripple and the applied dc voltage must not exceed the dc voltage rating of the capacitor. c. ripple current ratings by part number at 85 c and 40 khz are included in the table. ripple current correction factors for other temperature s and frequencies are given on the next page. d. transient reverse voltage surges are acceptable under the following conditions: the peak reverse voltage does not exceed 1.5 v and the peak current times the durati on of the reverse transient does not exceed 0.05 as. in addition, the repetition frequency of the reverse voltage surge is less than 10 hz. notes ? material at egress is tantalum ? insulation sleeving will lap over the ends of the capacitor case ? tinned nickel leads, solderable and weldable ? approx. weight: t1: 2.3 g, t2: 5.7 g, t3: 9.4 g, t4: 14.8 g dimensions in inches [millimeters] case code d 0.016 [0.41] max. insulated (dia.) l 1 + 0.031 [0.79] uninsulated e 0.250 [6.3] max. t1 0.188 [4.78] 0.219 [5.56] 0.453 [11.51] 1.500 [38.10] t2 0.281 [7.14] 0.312 [7.92] 0.641 [16.28] 2.250 [57.15] l2 0.281 [7.14] 0.312 [7.92] 1.008 [25.60] 2.250 [57.15] t3 0.375 [9.52] 0.406 [10.31] 0.766 [19.46] 2.250 [57.15] t4 0.375 [9.52] 0.406 [10.31] 1.062 [26.97] 2.250 [57.15] l 1 e e terminal location within 0.031 of center d dia. 0.025 + 0.002 [0.64 + 0.05] terminal welded to case 0.250 [6.35] max. 0.094 [2.38] max.
st www.vishay.com vishay revision: 03-feb-12 2 document number: 43000 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 ordering information st 220 100 t4 m i e3 super tan ? commercial cap. type capacitance f 85 c rated dc voltage case code capacitance tolerance insulating sleeve rohs compliant m = 20 % k = 10 % i = insulated x = uninsulated e3 = 100 % tin termination (rohs compliant) blank = snpb termination (standard design) standard ratings capacitance at 25 c and 120 hz (f) case code max. esr 120 hz ( ? ) max. dcl at max. imp. at - 55 c and 120 hz ( ? ) max. capacitance change at ac ripple 85 c 40 khz (ma) rms part number + 25 c (a) + 85 c/ + 125 c (a) - 55 c (%) + 85 c (%) + 125 c (%) 25 v dc at 85 c; 15 v dc at 125 c 120 t1 1.3 1 5 25 - 42 + 8 + 12 1250 st120-25t1mi 560 t2 0.83 2 10 12 - 65 + 10 + 15 2100 st560-25t2mi 1100 l2 0.5 3 25 7 - 60 + 20 + 45 3200 st1100-25l2mi 1200 t3 0.65 5 20 7 - 70 + 12 + 18 2600 st1200-25t3mi 1800 t4 0.5 6 25 7 - 72 + 12 + 20 3100 st1800-25t4mi 30 v dc at 85 c; 20 v dc at 125 c 100 t1 1.3 1 5 25 - 38 + 8 + 12 1200 st100-30tmi 470 t2 0.85 2 10 15 - 65 + 10 + 18 1800 st470-30t2mi 950 l2 0.5 5 30 7 - 55 + 18 + 35 3200 st950-30l2mi 1000 t3 0.7 7 25 7 - 70 + 10 + 18 2500 st1000-30t3mi 1500 t4 0.6 12 35 6 - 72 + 10 + 20 3000 st1500-30t4mi 50 v dc at 85 c; 30 v dc at 125 c 68 t1 1.5 1 5 35 - 25 + 8 + 15 1050 st68-50t1mi 220 t2 0.9 2 10 17.5 - 50 + 8 + 15 1800 st220-50t2mi 450 l2 0.6 3 25 7.5 - 45 + 12 + 30 2900 st450-50l2mi 470 t3 0.75 3 25 10 - 45 + 8 + 15 2100 st470-50t3mi 680 t4 0.7 5 40 8 - 58 + 10 + 20 2750 st680-50t4mi 60 v dc at 85 c; 40 v dc at 125 c 47 t1 2.0 1 5 44 - 25 + 8 + 12 1050 st47-60t1mi 150 t2 1.1 2 10 20 - 40 + 8 + 15 1800 st150-60t2mi 370 l2 0.6 3 25 9 - 33 + 9 + 20 2900 st370-60l2mi 390 t3 0.9 3 25 15 - 45 + 8 + 15 2100 st390-60t3mi 560 t4 0.8 5 40 10 - 58 + 8 + 15 2750 st560-60t4mi 75 v dc at 85 c; 50 v dc at 125 c 33 t1 2.5 1 5 66 - 25 + 5 + 9 1050 st33-75t1mi 110 t2 1.3 2 10 24 - 35 + 6 + 10 1650 st110-75t2mi 250 l2 0.8 5 30 12 - 30 + 6 + 15 2500 st250-75l2mi 330 t3 1.0 3 30 12 - 45 + 6 + 10 2100 st330-75t3mi 470 t4 0.9 5 50 12 - 50 + 6 + 10 2750 st470-75t4mi notes ? (k = 10 %, m = 20 %) and insulation letter (i =insulation, x = uninsulated) ? part numbers shown are for units with 20 % capacitance tolera nce and uninsulated capacitors. for 10 units, change the digi t following the letter x from 0 to 9. for units with outer plasti c-film insulation, subs titute 2 for 0 at the end of the part num ber ? for rohs compliant add e3 for suffix
st www.vishay.com vishay revision: 03-feb-12 3 document number: 43000 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 100 v dc at 85 c; 65 v dc at 125 c 15 t1 3.5 1 5 125 - 18 + 3 + 10 1050 st15-100t1mi 68 t2 2.1 2 10 37 - 30 + 4 + 12 1650 st68-100t2mi 120 l2 1.0 3 25 20.5 - 30 + 4 + 12 2200 st120-100l2mi 150 t3 1.6 3 25 22 - 35 + 6 + 12 2100 st150-100t3mi 220 t4 1.2 5 50 15 - 40 + 6 + 12 2750 st220-100t4mi 125 v dc at 85 c; 85 v dc at 125 c 10 t1 5.5 1 5 175 - 15 + 3 + 10 1050 st10-125t1mi 47 t2 2.3 2 10 47 - 25 + 5 + 12 1650 st47-125t2mi 90 l2 1.3 5 25 25 - 22 + 4 + 15 2000 st90-125l2mi 82 t3 1.8 3 25 40 - 35 + 5 + 12 1950 st82-125t3mi 100 t3 1.8 3 25 35 - 35 + 5 + 12 2100 st100-125t3mi 150 t4 1.6 5 50 20 - 35 + 6 + 12 2750 st150-125t4mi ripple current multipliers vs. frequency, temperature and applies peak voltage frequency of applied ripple current 120 hz 800 hz 1 khz 10 khz 40 khz 100 khz ambient still air temp. in c ? 55 85 105 125 ? 55 85 105 125 ? 55 85 105 125 ? 55 85 105 125 ? 55 85 105 125 ? 55 85 105 125 % of 85 c rated peak voltage 100 % 0.60 0.39 - - 0.71 0.43 - - 0.72 0.46 - - 0.88 0.55 - - 1.0 0.63 - - 1.1 0.69 - - 90 % 0.60 0.46 - - 0.71 0.55 - - 0.72 0.55 - - 0.88 0.67 - - 1.0 0.77 - - 1.1 0.85 - - 80 % 0.60 0.52 0.35 - 0.71 0.62 0.42 - 0.72 0.62 0.42 - 0.88 0.76 0.52 - 1.0 0.87 0.59 - 1.1 0.96 0.65 - 70 % 0.60 0.58 0.44 - 0.71 0.69 0.52 - 0.72 0.70 0.52 - 0.88 0.85 0.64 - 1.0 0.97 0.73 - 1.1 1.07 0.80 - 66 2/3 % 0.60 0.60 0.46 0.27 0.71 0.71 0.55 0.32 0.72 0.72 0.55 0.32 0.88 0.88 0.68 0.40 1.0 1.0 0.77 0.45 1.1 1.1 0.85 0.50 standard ratings capacitance at 25 c and 120 hz (f) case code max. esr 120 hz ( ? ) max. dcl at max. imp. at - 55 c and 120 hz ( ? ) max. capacitance change at ac ripple 85 c 40 khz (ma) rms part number + 25 c (a) + 85 c/ + 125 c (a) - 55 c (%) + 85 c (%) + 125 c (%) notes ? (k = 10 %, m = 20 %) and insulation letter (i =insulation, x = uninsulated) ? part numbers shown are for units with 20 % capacitance tolera nce and uninsulated capacitors. for 10 units, change the digi t following the letter x from 0 to 9. for units with outer plasti c-film insulation, subs titute 2 for 0 at the end of the part num ber ? for rohs compliant add e3 for suffix
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
